Slicer Discord
Cactus Cat Self Scratcher – Modelo 3D imprimible de MakerOnline MakerOnline
Cactus Cat Self Scratcher – Bild 1 Cactus Cat Self Scratcher – Bild 2 Cactus Cat Self Scratcher – Bild 3 Cactus Cat Self Scratcher – Bild 4 Cactus Cat Self Scratcher – Bild 5 Cactus Cat Self Scratcher – Bild 6
Household

Cactus Cat Self Scratcher

1.2k Descargas
518 Likes
0 Makes
Ver Modelo
Cactus Cat Self Scratcher / Self Groomer Bring a slice of the desert into your home with the Cactus Cat Self Scratcher! This quirky, cactus-shaped toy gives your cat a fun way to satisfy their scratching instincts. The built-in pot lets you add catnip, with small holes in the cactus body releasing the scent to lure your feline friend into play. This Cactus is a charming addition to any space that keeps your cat entertained and well-groomed! New Magnetic Version (Recommended) I’ve upgraded the Cactus Cat Self Scratcher with a magnetic mounting mechanism! This new version uses two pairs of round 6x2 magnets to securely attach the cactus body to the pot base, offering easier assembly and greater durability. It’s our recommended choice for most users due to its improved design. Dull Spikes Update Frequent comments suggested that original version had too sharp spikes - a new update adds profile with dulled spikes for those that like to play it safe. The tip diameter has been increased by 50% making the spikes dull, but not so dull that cats would get bored. Original Snap-Fit Version The original version features a snap-fit joint to connect the cactus body to the pot base. It’s still perfectly functional (mine hasn’t broken yet!), but the snaps can be delicate, especially when printed with materials like PLA Silk or if layer adhesion is weak. It’s a solid option if handled with care. Design Details Cactus Body: Measures 11cm tall, 9cm wide, and 5cm deep. Covered in conical spikes for scratching and grooming, with small holes for catnip scent to waft through. Pot Base: About 3cm tall and 6cm in diameter, designed to hold catnip. Assembly & Mounting For Magnet versions: place 2 6x2 round magnets on the backside of the cactus and inside the planter pot. The hole for the magnets is very tight, I recommend using flat-nose pliers to install the magnets (or use one size smaller magnet and glue it in) Mounting: Attach to a clean, dry vertical or horizontal surface using either st
Categoría
Household
Fuente
MakerOnline
Publicado
Actualizado
Lo que necesitas para imprimir: Avanzado Baja confianza
¿Por qué?
postproceso considerable
Tornillería requerida
Soportes 1/3
Ensamblaje 2/3
Ajustes 1/3
Tamaño de cama 0/3
Postproceso 2/3
Impresora
FDM / FFF
Formato de archivo
STL
Material
PLA, Silk PLA
Postprocesado
Pegado, Tornillería
Software
Cura, PrusaSlicer o similar
Mismo diseñador, más plataformas

Johnny_Bit también publica en

73 modelos adicionales en 1 plataformas más

Verificado por coincidencia de títulos de modelos entre plataformas.
Aún no hay valoraciones
Aún no hay comentarios – ¡sé el primero!

Modelos similares

6 Sugerencias
Feed Blog Slicer Calculadora Búsqueda por imagen Enviar Contacto Discord ☕ Buy me a coffee
DE EN FR ES IT NL

Añadir a colección