Thingiverse
iPhone 4S Case Flowers
por Woolpit
29
Descargas
24
Likes
2
Makes
Customized version of http://www.thingiverse.com/thing:40703
Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=40703
EN:
Case turned out. But! 1. In my program can not disable the mandatory layer of the substrate and eventually detach from the back wall of the patterned substrate was problematic. 2. Case turned on with a margin of 1 mm in length and width. That is, that the phone was held tightly in the case, will have to stick to the inner walls of the seal (foam tape).
In any case, many thanks to the creators - the team Makerbot!
RU:
ÐšÐµÐ¹Ñ Ð¿Ð¾Ð»ÑƒÑ‡Ð¸Ð»ÑÑ. Ðо! 1. Ð’ моей программе Ð½ÐµÐ»ÑŒÐ·Ñ Ð¾Ñ‚ÐºÐ»ÑŽÑ‡Ð¸Ñ‚ÑŒ обÑзательный Ñлой подложки и в итоге отделÑÑ‚ÑŒ заднюю узорную Ñтенку от подложки было проблематично. 2. ÐšÐµÐ¹Ñ Ð¿Ð¾Ð»ÑƒÑ‡Ð¸Ð»ÑÑ Ð½Ð° 1 мм Ñ Ð·Ð°Ð¿Ð°Ñом по длине и ширине. Т.е. что бы телефоÐ
Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=40703
EN:
Case turned out. But! 1. In my program can not disable the mandatory layer of the substrate and eventually detach from the back wall of the patterned substrate was problematic. 2. Case turned on with a margin of 1 mm in length and width. That is, that the phone was held tightly in the case, will have to stick to the inner walls of the seal (foam tape).
In any case, many thanks to the creators - the team Makerbot!
RU:
ÐšÐµÐ¹Ñ Ð¿Ð¾Ð»ÑƒÑ‡Ð¸Ð»ÑÑ. Ðо! 1. Ð’ моей программе Ð½ÐµÐ»ÑŒÐ·Ñ Ð¾Ñ‚ÐºÐ»ÑŽÑ‡Ð¸Ñ‚ÑŒ обÑзательный Ñлой подложки и в итоге отделÑÑ‚ÑŒ заднюю узорную Ñтенку от подложки было проблематично. 2. ÐšÐµÐ¹Ñ Ð¿Ð¾Ð»ÑƒÑ‡Ð¸Ð»ÑÑ Ð½Ð° 1 мм Ñ Ð·Ð°Ð¿Ð°Ñом по длине и ширине. Т.е. что бы телефоÐ
¿Has impreso este modelo? Inicia sesión y comparte tu make.
Inicia sesión para dejar un comentario
Iniciar sesiónAún no hay comentarios – ¡sé el primero!
